University of Messina

University of Messina Uses NI AWR Design Environment to Model Microwave Amplifiers
NI AWR Design Environment software is a very valuable tool for teaching and research. It offers an impressive tuning action required for model performance refining that also allows students to quickly and clearly understand the effect of each model element on the device scattering and noise parameters.
Alina Caddemi and Davide Aloisio
Full Professor of Electronics and PhD Researcher
University of Messina

University of Messina Uses NI AWR Software to Model Microwave Amplifiers

Company Profile

The University of Messina, located in Messina, Italy, has always been characterized by its high quality of research and teaching. It is committed to European higher education so as to foster mobility, increase employment, and attract students and academics from within as well as outside Europe. The University of Messina participates in partnerships with foreign universities, promotes international research projects, and supports European and international exchange programs.

The Design Challenge

The University of Messina Microwave Electronics Lab (EleMIC) uses NI AWR Design Environment™ software for research and all microwave electronics education levels (B.S., M.S., Ph.D.). The challenge for Prof. Caddemi is to not only introduce her students to the secrets of microwave circuit analysis and design but also to make it a truly exciting experience.

Of particular interest to Prof. Caddemi is device modeling. In this domain, she and her group have 25 years of experience and more than 200 international papers published. A tough benchmark has been the design of single-stage, high-power microwave amplifier using complex device models for nonlinear analysis of the device behavior as well as optimization. The group recently used Microwave Office circuit design software to tune the behavior of a gallium arsenide (GaAs) high-electron mobility transistor (HEMT) wafer previously characterized in the microwave range (2-18 GHz) under dark and laser-light illuminated conditions. A key challenge was the noise analysis and modeling aspect that was markedly changed by the light exposure. 

The Solution

NI AWR Design Environment fulfills the EleMIC’s requirements for having very agile software tools to accomplish the fine tuning required for model refinement, complete and versatile nonlinear analysis tools, and easy management of layout generation for EM simulation. For the work presented in the IEEE conference paper, the software was used to analyze in detail the performance changes of a GaAs HEMT-based low-noise amplifier under visible (650 nm) laser exposure. The device employed was first characterized in dark and illuminated conditions over the 2-18 GHz frequency range in terms of DC, scattering and noise parameters. Subsequently, it was modeled by means of a linear circuit model with associated noise sources in both conditions. By employing the experimental results, a low-noise amplifier was then designed and optimized for dark-mode operation in the 7.5-8.5 GHz frequency range. Finally, the performance of the LNA under light exposure was evaluated. 

On the basis of device performance variations under VIS light exposure, either a severe degradation of the noise figure, a slight increase of the amplifier gain, or a moderate variation of the input/output matching was expected. Instead, the obtained results exhibited a moderate degradation of the overall LNA performance due to device illumination, except for the input matching level which showed to be improved. NI AWR Design Environment was then used to analyze the correlation between the device model variations and the amplifier behavior to get a deeper insight into the observed trends.

On the basis of measured results, a low-noise amplifier was tailored on the device performance in dark conditions. The design was carried out Microwave Office, with performance goals centered in the 7.5 to 8.5 GHz frequency band. Alumina (εr = 9.9, tg δ = 0.0002, h = 250 μm) was adopted for the substrate with 5 µm-thick gold metallization. The amplifier gain is above 10 dB, while the noise figure is 1.4 ± 0.15 dB over the entire band. Either input and output matching levels stay higher than 10 dB within the chosen frequency band. The stability was monitored either inside and all over outside the operating band by the value of coefficient. Modeling of the bonding wires has been accomplished by means of the resident multilevel bond wire model BWIRES2 that define bonding scheme parameters in compliance with EIA/JEDEC Standard No. 59. 

Due to the required stabilization of the amplifier, we noticed that the reflection coefficient “seen” on the left side of the device input was not really close to Γopt within the operating band, i.e., broad-band stabilization was achieved at the expense of the noise mismatch.

Why NI AWR Design Environment

Prof. Caddemi chose NI AWR Design Environment software because it has a very user friendly interface, is easy to use, has a very good element help function that is highly beneficial for educational purposes, has powerful optimization capabilities and achieves very fast and accurate EM analysis. Productivity, ease of use, simulation speed, availability of models, and technical support were cited as the most helpful features. For Prof. Caddemi, the most valuable aspect of the software is that it is a powerful tool suite for both expert engineers and novice students. 

Emanuele Cardillo (PhD student) in the lab using NI AWR software. 

To continue to read the full story, click to download the PDF document below...

Related customer stories

The Microwave Office intuitive environment, the interaction of all of its simulation engines, and its integration with third-party design tools has enabled us to develop a seamless, first-time-right design process for our RF/microwave amplifiers.
Ivan Boshnakov
Senior Principal Engineer
Aerial Facilities Limited
Read story
The seamless integration of the Microwave Office and VSS software gave me more meaningful results because I was able to simulate my power amplifier circuit design’s response to the EDGE/GSM modulated input signal with one design platform. I used Microwave Office and VSS from circuit concept all the way through to product completion. I was exceptionally happy with the technical quality of the ACPR and EVM simulation results.
TriQuint Design Engineer
TriQuint (now Qorvo)
Read story
We were unable to EM this entire structure using any other EM solver and turned to AWR to give it a try. The insights gained as unveiled by AXIEM opens up new vistas in mm-wave design for Mimix.
Dr. Simon Mahon
Director of MMIC Design
Mimix Broadband (now part of M/A Com)
Read story